Ghost Controls Hinge & Roller Replacement Nationwide

Ghost Controls Hinge & Roller Replacement: The Santa Clarita Owner’s Guide

We stock and install Ghost Controls hinge and roller replacement hardware across Santa Clarita, with most hinge sets running $185 – $340 installed and roller kits between $90 – $180 depending on your gate’s weight and post condition. Most jobs are completed in a single visit, usually under two hours. You’ll typically notice the problem before you name it: the gate drags on the ground, whines when it moves, or sags visibly toward the latch post. In Santa Clarita’s dry heat and Santa Ana winds, the nylon rollers on Ghost Controls gates dry out and crack faster than the manufacturer’s general lifespan predictions, and that’s exactly what we see in neighborhoods like Valencia, Saugus, and Canyon Country.

Call (661) 425-9011

Which Ghost Controls Models This Applies To

Ghost Controls builds three main residential lines: the single-swing TSS1, dual-swing TDS2, and the heavier TSS1XP and TDS2XP kits, which include the larger solar panel and higher-torque operator. The hinge and roller hardware differs across these lines, and here’s the compatibility gotcha most owners miss: the TSS1XP uses a 22mm hinge pin and a steel-backed roller bushing, while the standard TSS1 uses a 20mm pin with an all-nylon roller. They look nearly identical on a bench, but the XP hinge will not seat properly in a standard TSS1 bracket without reaming, and the smaller pin in an XP bracket will wobble and wear the bore oval within a season. If your gate’s roller plate is stamped with the model suffix “XP” anywhere on the mounting face, you need the XP-spec parts, full stop.

For Santa Clarita homeowners, we usually recommend OEM Ghost Controls hinges when the post is original and the gate has been operating on Ghost hardware since day one, because the post hole spacing matches without shimming. On gates where a previous owner mixed in a generic farm-store hinge, we can supply a quality aftermarket equivalent from brands like US Automatic or Aleko, which use the same 20mm pin spec and are genuinely interchangeable on the standard TSS1/TDS2 lines. We stock both on the truck so the swap doesn’t stall. Warden Gate Repair Santa Clarita is an independent service provider; we are not affiliated with Ghost Controls, but we install their parts and know their tolerances.

Signs Your Ghost Controls Hinge & Roller Replacement Is Failing

• The gate scrapes the driveway or drags a crescent into gravel. The roller has flat-spotted or the nylon rim has worn through to the steel hub. On a Ghost Controls cantilever-style gate, the lower roller carries the entire leaf weight, so wear shows up as a lean first, not a noise.
• A whine or chirp that wasn’t there last season. The roller bearing inside the nylon wheel has lost its grease and is running dry. Santa Clarita’s summer heat thins what little grease these sealed bearings come with, and once it’s gone, the bearing gauls quickly.
• The gate wants to rest against the opposite post instead of hanging straight. The hinge pin or hinge barrel has worn, usually on the lower hinge. You can confirm it by lifting the gate leaf; if the leaf kicks upward at the latch end when you lift the free end, the pin is sloppy.
• The operator labors to move the gate. A worn roller increases rolling resistance just enough to make the motor work harder, especially on the first cycle after the gate sits in the sun. Over time it burns out the control board prematurely, and a $22 roller becomes a $300 board.
• You hear a hard “clunk” when the gate closes fully. This is the gate dropping over a worn roller instead of rolling into the closed stop. The open and close limit positions can be perfect, but a sagging leaf changes the geometry at the striker, and the clunk is the gate’s weight landing on hardware it shouldn’t.

Replacement Cost & What’s Included

In Santa Clarita, expect the following installed prices:

• Standard TSS1 / TDS2 hinge replacement (single pair): $185 – $265
• TSS1XP / TDS2XP hinge replacement (single pair): $240 – $340
• Roller kit replacement (one gate leaf, both rollers): $90 – $180
• Hinge and roller combo (one leaf, complete): $260 – $470

The spread comes from gate weight, post condition, and whether the old hardware has been welded by a previous repair, which is common on older Canyon Country properties. Every Warden Gate Repair Santa Clarita job includes parts and labor, plus the written price given before any work starts, so there’s no surprise at the end. Our 365-Day Done Right Promise covers the replacement in writing: if it fails within a year, the return visit is free. That’s not a sales line; it’s in the estimate and on the invoice.

DIY or Call Us?

You can safely do a visual check: lift the gate leaf, listen for clunks at the hinge, and spin the roller to feel for roughness. That’s worth five minutes and confirms what’s failing. Replacing the parts is a different job. The hinge pin on any Ghost Controls gate carries the full weight of the leaf, and when the pin comes out, the leaf wants to fall; we’ve seen fingers pinched and gate glass cracked. The roller replacement on a sagging gate also means re-plumbing the leaf and re-teaching the operator limits, which most homeowners get wrong on the first pass. If the roller is chattering or the gate’s leaning enough that the latch no longer lines up, call us at (661) 425-9011. Cole Rafferty will quote the parts and the labor honestly over the phone, and the written price is what you’ll pay.

FAQs